Professionals
How to prepare a cocktail station for aquafaba sours
Before the first tickets land, set a dedicated sour lane with your aquafaba, jigger, tins, ice access and labeled bases. Keep the aquafaba out of every batch and measure 20 ml per drink at the shake, so each sour follows the same station routine.
A packed rail exposes small gaps fast. A carton left at the wrong temperature, a jigger parked across the well or a base bottle without a clear place interrupts the build. Set the station so the sequence stays visible: pick up the base, measure the aquafaba, dry shake, add ice, then shake again. This setup works across Pisco Sours, Whiskey Sours, White Ladies and the other sours you already pour.
Updated: .

What goes on the station before service?
Build the lane before the first call, not while a sour ticket is waiting. Put clean shaker tins, a Hawthorne strainer, a jigger and a clear route to ice in the order you use them. Keep the carton in its cold holding spot, then bring it to hand only for the pour.
| Item | Where | Check |
|---|---|---|
| Carton | Fridge | Opening date marked, held at 2 to 6 °C |
| Jigger | Next to shaker tins | Clean and ready for 20 ml |
| Pre-batched base | Reachable station position | Spirit, citrus and syrup only |
| Shaker tins | Start of the sour lane | Clean and ready to dry shake |
Use one station pattern for every sour on your list. That gives you a visible check before the shaker leaves the rail, rather than asking yourself where an ingredient or tool went mid-round.
How do you place the aquafaba and the jigger?
Keep the opened carton in the fridge at 2 to 6 °C. Set the jigger beside the shaker tins, on the hand you use to build the drink. That layout lets you measure the aquafaba just before the dry shake, rather than pouring by eye.
Date the carton when you open it. Return it to the fridge between rounds, even when the rail is busy. Measure 20 ml into the tin, dry shake for 10 to 15 seconds without ice, then shake for 10 to 15 seconds with ice. Keep the jigger clear of syrup residue so its measure stays readable.
How do you set the pre-batched bases?
Set pre-batched bases where you can reach them without crossing the sour lane. Build each base with the spirit, citrus and syrup. Leave aquafaba out of the bottle, because it goes into the shaker at the time of the shake.
For 40 Pisco Sours, that's 1,600 ml of pisco, 800 ml of fresh lime juice and 800 ml of aquafaba. Keep the aquafaba portion separate from the batch and measure it as each order is made. Label the base with the drink name, then position the carton and jigger beside it. The same rule applies whether you are preparing a Whiskey Sour, Amaretto Sour, Gin Fizz or White Lady.
What do you check at the end of the night?
Close the station with the carton first. Check that its opening date is visible and that it has gone back into the fridge. Opened liquid keeps for 3 to 4 days at 2 to 6 °C, so the date is part of the close-down check, not an afterthought.
Rinse and put away the jigger, shaker tins and strainer. Remove empty base bottles and leave the next service with a clear place for each sour tool. Unopened liquid and powder keep for at least 12 months at room temperature. If you change a build or station order, write the new steps into your process sheet before the next service.
Before your next service, stand at the rail and run one sour from the labeled base to the fridge return. Move any tool that makes you cross the lane, date the carton when it opens, and keep the 20 ml jigger measure in its fixed place. If you need ready-made aquafaba for your bar, send an enquiry.
Where to buy VERY AQUAFABA


